This page needs to be proofread.
SHEARING MACHINES]
TOOL
37


to the teeth, should undue stress come upon the saw. This is usually effected by the use of weights or springs, which allow a certain freedom or latitude to the driving gears. The work is held by screw clamps, V-blocks being required in the case of circular objects. A number of pieces, such as shafts, rails or girders, can be fastened down close together in a pile and cut through in one operation. There is a very useful class of circular saw, the flush-side (fi . 55), tlfat is valuable for cutting close up to a surface. The disk is bolted to a flange on the end of the spindle with countersunk bolts, so that the face is uite fiat. Another class of saw used for dealing with girders and (bars is carried in bearings upon a pivoted arm, which is pulled downwards by a weight to give the feed. The work is bolted to a table below the saw. Ample lubrication, by oil or soapy water, is essential in cutting wrought iron and steel; it is pumped on the blade, keeping it cool and washing away the cuttings. Band-saw machines resemble in outline the familiar types employed for sawing wood, but they are necessarily stronger and stiffer, and the saws run at a much lower speed. The tables, moreover, differ in possessing compound slides for moving the work and in the provision of a series of slots on the top table, whereby the object to be sawn is secured with bolts and clamps. The tables are moved automatically or by hand. The rate of cutting must be varied according to the thickness of metal. Lubrication is effected by running the lower saw pulley in a bath of oil or soapy water, which is carried up, so keeping the blade cool and “ easing ” the cut. The reciprocating class of saw has until recently been confined to small types for workshop use, termed hack saws, which have a small blade ranging from 12 to 18 in. long. This is strained between a couple of bearings in a frame which is reciprocated above the work clamped in a vice. An arrangement of weights feeds the saw downwards. The larger hack saws cut off bars and girders up to 12 in. across, and in some there is a provision introduced for giving intermittent rotation to the bar, thus presenting fresh faces to the saw. The hack saw is of great utility for comparatively light work, and, as the smallest blades are cheap enough to be thrown away when worn out, there is no trouble and expense connected with their sharpening, as in the circular and band saws. An adaptation of the reciprocating saw is that of the jig type, which has a small blade set vertically and passing up through a table on which the work is laid. It is handy for cutting out dies and various curved outlines, in the same manner that fret-sawing in wood is done. VIII.-SHEARING AND PUNCHING MACHINES P These have much in common as regards their mode of operation. They are actuated either by belt and s ur gearing, by steam-engine, by electric motor, or hydraulically. Tliie first named is only suitable where arrangements can be made for driving from a line shaft. In view of the great convenience of the other methods of driving, they are coming into greater use, especially for ship-yards and other works where shafting is undesirable or inconvenient. For boiler makers' and platers' use the function of punching, and shearing are usually combined in one machine, the rams being placed at opposite ends and actuated from the same source of power. The last shaft in the train of gearing is set to bring its ends within the boxes containing the rams, and eccentrics on the shaft are moved

FIG. 57.-Steam Hammer, 'small Overhanging Type. (B. & S. Massey, Manchester).

Standard.

B, Base-plate.

Anvil block (independent of standards). Tup or hammer head.

E, Pallets, or forging blocks, attached to anvil and tup. Steam cylinder.

Piston, solid with piston rod H. Piston valve, regulating period of admission of steam, operated by hand by lever K or lever N.

Stop or throttle valve for controlling admission of steam to valve chest, operated by hand lever M. Lever in contact with roller on tup D, which moves the valve J automatically as the tup rises and falls. Lever for pre-adjusting the range of movement of N and J, according to its setting in the notches of the quadrant from within die blocks fitted to the rams, so that as the shaft revolves it a to b. causes the rams to move up and down and operate the shear blade and Steam supply pipe from boiler. Q, Exhaust steam pipe. the punch attached to the bottom end. Another class of machines is workedl by mezgns of masséve leversi 1 'Z ' ' . -Q ' ~ C - H 5| pivote in the raming, an actuate li I' i " I | ' ii .-.gl E by cams on the driving shaft which il "" fl 9/¥ 5' » ~ 'E § ° ' 'A —°~“i| cause the levers to rock and move 1| ;», '.=, ~. . 1 F*—“"!§ . I 1~ ~-*Q —.1

I, f ' C, ~ .' REIIBUQIH; /' ' F 5 the punches or shears up and down

lr- ., =— -~5 °'~ ' M i ""' “Q ""' by the opposite ends. The punch I' I * 5=—~ - 'g . /U '—'- -"1" jf . ~ slides are constructed to “ dwell”

  • I; -Z I '; 4 j G'l 11 5 '; for a short eriod at the top of the
| . »0 - =~-.V ~— 1 X. - ' P - — I:

| 1. I. 5 pf 5 - 1 4 1 stroke at each revolution, thus giving H 1 » g i;/K ' ' J Q the attendant time to place and ad; H: ' 2 ' * I g 5 just the plate accurately beneath the G, -Ug i, ' 2 { ' punilh. The same effect tis obtsiined | N = in the eccentric types o mac mes © gg mentioned above, by a disengagmg

  - E motion, which istlirown in by touching

@ ~ @: H a lever, thus stopping the punch until ?—~'—~'*;& the operator is ready for its descent. 1 i I:; Thi mo11;e complete giachines have an I 1 ange s ear situate centrally, wit A I . .

° l -i ~ ~ V-blades for severing angle iron. The

J ' I lar est forms of shears for massive
 ' g 1

~ /' plates, usually have the blade recipro-5, cated by crank or eccentrics on the ~-V" ' W ' '~ r' " ““'~ ' M -"~>~“>f' f ~ Am' ' '~ f W - 5' driivirilg il};1aftl, é:oupled by connecting-F IG. 56.-Hydraulic Punching and Shearing Machine. (Musgrave Brothers, Leeds.) roliygrauis lpshching and shearing A, iframe. E, Punch. I, K, Main and return rams for machines are used largely on account B Shear blades, set angularly. F & G, Main and return rams ditto. of their convenience, since they dis-C, Ram for operating blade. for punch. L, , N, Attendar1t's control- pense with all belts, engines or motors D, Smallram forreturmngditto. H, Ang e shear. ling handles. in the vicinity, and giveaverypowerful